Raymond Mill, also known as Raymond Mill, English full name: Raymond mill. It applies to a variety of mineral powder preparation, pulverized coal preparation, such as raw materials, gypsum mine, coal and other information of fine powder processing. Raymond Mill, Raymond Mill, efficient Raymond Mill, high pressure roller mill.
- 1, Raymond Mill site has not yet equipment, should be properly kept, revealing the appearance should be coated with anti-rust grease, and to prevent the sun and rain, to prevent the body rusty water, to establish conservation criteria.
- 2, the plant and the foundation should be based on Raymond grinding equipment foundation map scale should meet the height and equipment orientation, Raymond Mill should use high standard cement and should be buried in the steel can only pour the foundation, and buried pipe Or cable trench. After the cement foundation is poured, it is necessary to have a 15-day conservation period.
- 3, should be equipped with 2 to 3 tons of lifting things for Raymond Mill equipment repair.
- 4, Raymond Mill from the factory to the use of time beyond 6 months, the host base shaft system, transmission equipment, roller equipment, analysis of oil sumps should be clean to see, clean the end of the inspection should meet the parts to meet Smooth oil.
- 1, the first drive equipment into the pit filled with the base, pay attention to control a certain height, and then use the level of proofreading on the top of the plane, together with the drive equipment equipment in the face of the fixed with bolts.
- 2, Raymond Mill host equipment. Before the device should be in the bottom of the base of the plane and the base of the cement touch and the anchor bolts on the pad between the rubber shock pad (see photo), and then use the box level level proofreading base "B", the calibration point for the interdisciplinary line four points together Adjust the two halves coupling ", and its different axis degree should be less than 0.20 mm, E1 and mdash; E2 non-parallelism shall not be greater than 0.1 mm, and" l " The gap should be kept within 5-8 mm.
- 3, the direction and height of the pipeline equipment should be according to the total map equipment, shall not be arbitrarily altered and heightened, the pipeline junction should be sealed, tightened after the leak can not appear. Electrical equipment should be accurate and reliable, to be the end of the equipment should be carried out after the test machine.
- 1, empty load test machine, in the no load before the test machine, roller equipment should be tied with steel wire rope to prevent the impact of grinding roller and grinding ring, and then the host air test machine not less than 1 hour; Operation should be smooth, the oil temperature within the box should not exceed 80 ℃, the temperature does not exceed 40 ℃. The direction of rotation of the host and the analyzer.
- 2, the blower should be no load, until the normal operation and then load, and then investigate the smooth operation, no abnormal noise and oscillation, rolling the maximum temperature shall not exceed 70 ℃, the temperature rise shall not exceed 35 ℃.
- 3, the load operation test machine moment of not less than 8 hours, Raymond grinding operation after the normal machine without abnormal noise, the pipeline at the junction without air leakage, after the test machine again tighten the tightening, you can put Normal use.
- should look at all the repair doors closed is not close, see the crusher palmar plate gap is not fit the feed size scale, adjust the analysis machine speed should reach the approximate particle size requirements. The final order in order to boot.
- 1, start the bucket elevator;
- 2, start jaw crusher;
- 3, the material to be stored after the material, start the analysis machine;
- 4, start the blower (empty load, to be normal operation and then loaded);
- 5, launched Raymond Mill host, in the launch of the host immediately launched an electromagnetic oscillation feeder. At the moment Raymond Mill grinding work is the beginning of
- The concise operation sequence is as follows: Launch: hoist & rarr; crusher & rarr; parser & rarr; fan & rarr; host & rarr; feeder.
- Raymond Mill should shut down each machine in the following order:
- 1, first turn off the feeder to stop the feed;
- 2, stop the host after about one minute;
- 3, blow the residual powder after the suspension of the blower;
- 4, the final closure of the analysis machine.
- Raymond Mill downtime is: Feeder & rarr; Host & rarr; Blower & rarr; Profiler.
- Crusher machine manufacturer Nigeria
- Gold ore crusher machine Nigeria
- Mobile crushers for sale Nigeria
- Talcum powder processing plant Nigeria
- White coal crushing machine Nigeria
- Crusher in cement plant Nigeria
- Power plant coal crusher Nigeria
- Sandstone Quarrying And Processing Nigeria
- Iron ore mining equipment Nigeria
- Iron Ore Mobile Crusher Nigeria
- Jaw and cone crusher Nigeria
- Crusher machine for feldspar Nigeria
- dolomite powder milling machinery Nigeria
- Concrete block making machine Nigeria
- Coal crusher for sale Nigeria
- Coal grinding mill machine Nigeria
- Brick crusher for sale Nigeria
- Ball mill for cement Nigeria
- Barite Ore Grinding Plant Nigeria
- Basalt artificial stone crusher Nigeria
- Basalt Stone Crushing Plant Nigeria
- Afghanistan Coal Processing Line for Sale Nigeria
- Air Classifier For Mineral
- Ball Mill Development Prospect Nigeria
- ：[email protected]